The Process Of Water Dechlorination At Home

At times, diseases causing bacteria can find its way into water. As a homeowner, you will need to disinfect this water, to ensure its safety. At most, the first and commonly known disinfectant is chlorine. The act of purifying water with this substance is called chlorination. In short, this water treatment procedure deals with disease-causing bacteria, parasites and other living organisms. In as much as this is the right method to treat your water before using it, it has its disadvantage. Among the many disadvantages available, the below are a few most common ones;


First, the substance usually cause bad taste and smell. Luckily, chlorine is not poisonous to both human and animals, however if the ratio used in treating the water surpasses the expected ration, then it means water will be concentrated with chlorine. In this way, water will have awful taste, consequential in reduced water use. Fortunately, charcoal can be used to reduce the chlorine concentration in water. Secondly, a continuous consumption of chlorinated water can cause cancer. This is because; chlorinated water at times can form trihalomethanes substance, a substance that is responsible in causing cancer.

Apart from the above, it is sad to understand that even though water is treated with the introduction of chlorine substance to it, chlorine cannot remove Nitrate. The only thing that chlorine does is to prevent nitrates from being reduced to nitrite, a substance that is known to be dangerous for human consumption, however it does not eliminate nitrate. For further reading on the same, feel free to check out this link Cyber Nook.

The Process of Cleaning Pool Water

Chlorine kills bacteria in a simple reaction. The chlorine solution first breaks down into several chemicals. Among the chemicals, Hypochlorous acid and hypochlorite ion dominates the action. They both function in almost the same way when tackling the bacteria. Their first point is to attack lipids, found on the cell walls, thus destroying enzymic structures inside the cell. This action renders them harmless and oxidized. Working of the above chemicals is the same, only that they vary in working rate. Hypochlorous acid has the ability to corrode organisms in seconds, divergent to hypochlorite a ion, which takes up to almost a half an hour. Consequently, this feat establishes the period, which treated, water can be said to be secure for use, following the primary treatment.

What should be noted before treating pool water is the pH level. If the pH is noted to be high, then the treatment process might take long since HOCl will not be enough to take on the process as required. The ideal pH condition should be 7 and 8. Therefore;

  • The first step to consider is to ensure pH is considerable. Test your swimming pool water.
  • Second, balance the pool pH. This will be done by adding either a base or an acid.
  • Check filter, if it is working well, and then do the scrubbing, scrub sides, as well as the bottoms of the pool.
  • The third thing is to treat the pool, with shock pools. At most, pool shock bears a bit high levels of chlorine and this is what wipes out the sanitization and the algae content in the pool. The best pool shock to choose is almost 70 percent, given that this is recommendable in eroding the tough algae. After this, usher in the final step, which is finishing the job. Here, the dead algae are supposed to be vacuumed up. Do this thoroughly to ensure all algae have gone.

Drinking Water Filters

In the same way, drinking water filters are supposed to be cleaned so that they can give out clean water for drinking. Instead of replacing drinking water filters, they can as well be rinsed in chlorinated water. First, clean the filters to remove sediments. Then soak in chlorinated water to kill the bacteria that might be as a result of the cleaning time. Wait until it is dry, and then refit in the water tabs. The process is not costly, since you only require getting water supply and the chlorine. Drinking water and shower waters are treated in the same way. The only difference is the channel that they pass before reaching the consumption point.

Shower waters and drinking or cooking water at times can be collected at one point, and then treated from that point, before being discharged to the various places for utilization. Thus, the initial step is to coalesce the water, here particles are made to settle as masses and not individuals. Then sedimentation is followed, then filtration and lastly disinfection. Disinfection is done by the use of chlorine. Before this treated water is taken to bath rums, bathtub should be treated as well. For main grade bathtub, buying and installation can range from 621.16 to 867.23 dollars. It is expensive and therefore, it does not require to be bought every time rather, it is better to clean it when filthy, to uphold its work ability. Marshal it into the tubes chlorine, and then wait for some thirty minutes, before passing water at a high pressure through the pipes.

Showers also need to be cleaned. First, during installation, ensure the shower you buy has quality shower heads like the ones in the link below; Rainshower CQ1000 Dechlorinating Shower Filter the best way to clean the shower head is by using vinegar. It is easy, simply fill a bag with vinegar, tie it around the showerhead, ensuring it submerges in the liquid, and wait for some minutes. Apart from the above method, you can as well place the showerhead in the source pan and add white vinegar and heat. This is also the best way of cleaning up showerheads. All the gadgets and chemicals for treating water and water related equipments can be obtained from water department or nearest shops.

Leave a Reply